On a residential job, the nailer runs fast and nobody stops to think about every shot. Yet the nail holding a sill plate and the one fastening a subfloor have different jobs to do. Collation, diameter, shank and finish should be chosen for the connection. A wrong choice does not show right away. It turns up a few years later, when the floor starts to squeak or the nails in a deck begin to rust.
Strip or coil: two formats, two uses
For structural framing (walls, floors, trusses, window bucks), crews mostly work with strip nails, in one of two formats.
21° plastic strip carries nails from 2" to 5", in diameters from .113" to .148". It is the most versatile format: walls, subfloors, sheathing, decking. Plastic collation handles moisture well, but it shatters on firing and leaves fragments on site.
33° paper tape holds clipped-head nails, which pack more tightly in the magazine. Shur-Fast offers it in 2-3/8" and 3-1/4", in .113" and .120" diameters, for floor and wall framing, truss build-up and window build-up. Paper leaves no debris but does not like rain, so keep the strips dry.
15° coil nails mostly go elsewhere: sheathing, siding, fencing and decking. Their thinner diameter (.092" to .099" in our plastic coil range) and the high capacity of a coil suit long runs of repetitive fastening.
Whatever the format, the collation angle has to match the tool. A 21° strip will not feed properly in a nailer built for 30° to 34°, and the reverse is also true.
Diameter and length: the plans decide
As a rule, a longer and thicker nail holds better. It also splits wood more easily near edges and in dense species, so the choice is made connection by connection.
For structural members, nail length, diameter and spacing are not left to the crew's judgment. They are set by the plans, by Part 9 of the National Building Code and by the applicable provincial code. When in doubt, the designer or the inspector decides. Our job is to supply the size specified, in the format that fits the tool on site.
Smooth, ring or screw: the shank sets the hold
A smooth shank suits most interior framing connections. It drives easily and costs less.
Where the wood moves, a ring shank resists withdrawal better. Subfloors are the usual case: a nail that slowly backs out ends up causing squeaks. Ring shank also suits exterior connections exposed to freeze-thaw cycles.
For dense wood and connections subject to vibration, a screw shank offers the highest withdrawal resistance of the three.
In plastic strip, we also carry duplex (double-head) nails for temporary work such as formwork and temporary bracing. The second head stays proud of the surface, which makes removal easier.
Finish depends on exposure
In interior framing protected from the weather, a bright nail is enough. As soon as a member is exposed to moisture or in contact with treated wood, move to hot-dipped galvanized (meeting ASTM A153 Class D) or 304 or 316 stainless. Sill plates and decks are often treated lumber, and the copper compounds in that wood attack a poorly protected nail. We covered how that happens in Why Your Fasteners Rust in Treated Wood (and How to Stop It).
Framing in winter
Framing does not stop when the cold sets in. Frozen wood is harder and less flexible, and it splits more easily when nailed. Point, shank and coating choices have to follow. Those adjustments are covered in Why Do Your Fasteners Fail at -20°C? Solutions for Frozen Wood.
The nail and the nailer work as a system
A well-chosen nail that does not suit the nailer causes jams and wears the tool faster. Depending on the format, our strip nails are compatible with the leading framing nailers on the market, including Bostitch, Paslode, Senco, Hitachi, Makita, MAX and DeWalt. Before a volume order, we can confirm compatibility with the model your crews use. For care of the tool itself, see Pneumatic Nailer and Stapler Maintenance: The Habits That Extend Tool Life.
Formats, diameters and compatible tool models are listed on our Plastic Strip Nails and Paper Tape Nails pages. For a question about format or compatibility, our team can be reached at 1-800-667-3061.